Electric Arc Flash PPE

According to the NFPA 70E, Arc Flash is a “dangerous condition associated with the release of energy caused by an electric arc.” It is measured in terms of arc flash incident energy E (AFIE), which is used to determine the level of Personal Protective Equipment (PPE).

An arc flash is the light and heat produced from an electric arc supplied with sufficient electrical energy to cause substantial damage, harm, fire, or injury. This can occur near high power electrical equipment such as transformers, service entrance switch gear or generators.

The first step to protection conduct an Arc Flash Hazard Analysis which defines the procedures and limits the damage of electrical arcs on personnel and, by measuring the released energy, defines the risk and determines the relevant level of the PPE required.

 HRC* 0 –  0 cal/cm2 ; 0 J/cm2: Non-melting, flammable materials (i.e untreated cotton, rayon, wool, silk or blends of these materials) with a minimum fabric weight of 150g/m2
 HRC* 1 – 4 cal/cm2 ; 16,74 J/cm2: Arc Rated Flame Retardant shirt, Flame Retardant trousers or Flame Retardant coverall
 HRC* 2 – 8 cal/cm2 ; 33,47 J/cm2: Arc Rated Flame Retardant shirt, Flame Retardant trousers or Flame Retardant coverall
HRC* 3 – 25 cal/cm2 ; 104,6 J/cm2: Arc Rated Flame Retardant shirt and FR trousers or FR coverall, and arc flash suit selected so that the system arc rating complies with the required minimum
HRC* 4 – 40 cal/cm2 ; 167,36 J/cm2: Arc Rated Flame Retardant shirt and FR trousers or FR coverall, and arc flash suit selected so that the system arc rating complies with the required mini

*HRC:  Harzard/Risk Category

Selecting the correct level of Arc Protection Equipment (APE) is made easy from this table however there are a few questions to ask your APE supplier:

  • Is the garment compliant with SANS 724:2010, NFPA 70E:2009 and SANS 984/IEEE Std 1584?
  • Can they send you the relevant certifications?
  • Does the garment meet your required HRC level?
  • Has the garment been tested? (not the fabric – very important)
  • If so, can they send you the test reports that include photos?

It’s important to note that where more than 40cal/cm2 APE is required it is not recommended unless all other means of reducing the risk of exposure has been investigated.

The Arc PPE you use really is your last line of defence, and following the above steps ensures that you are doing the best you possibly can to minimise injuries as a result of an arc flash incident.


Information supplied by: Dromex Personal Protective Equipment.

ISO45001 on our doorstep

ISO45001 one of the world’s much anticipated standards for occupational health and safety (OHS), has been approved as a Draft International Standard.

Every 15 seconds, a worker dies from a work-related accident or disease, and 153 people experience a work-related injury. These represent an enormous burden for organizations and society as a whole, costing over 2.3 million deaths a year, not to mention the more than 300 million non-fatal accidents*.

Now, with ISO 45001 at the Draft International Standard (DIS) stage, the world is one step closer to a robust and effective set of processes for improving work safety in global supply chains. Designed to help organizations of all sizes and industries, the future standard is expected to reduce workplace injuries and illnesses around the world.

More than 70 countries are directly involved in the creation of this important document, being developed by project committee ISO/PC 283, Occupational health and safety management systems.

“Implementing a strong occupational health and safety management system helps organizations reduce accidents and ill health, avoid costly prosecutions, perhaps even reduce insurance costs, as well as create a culture of positivity in the organization when its people see that their needs are being taken into account,” explains David Smith, Chair of the committee. “Wide adoption of ISO 45001 should reduce the horror stories in the media of poor OHS management leading to loss of life, injury and large-scale disasters, as seen in the factory buildings around the world.”

ISO 45001 is based on the common elements found in all of ISO’s management system standards, assuring a high level of compatibility with the new versions of ISO 9001, Quality management systems, and ISO 14001, Environmental management systems. It uses a simple Plan-Do-Check-Act (PDCA) model, which provides a framework for organizations to plan what they need to put in place in order to minimize the risk of harm. The measures should address concerns that can lead to long-term health issues and absence from work, as well as those that give rise to accidents.

Now that ISO 45001 has advanced to the DIS stage, national member bodies of ISO have been invited to vote and comment on the text of the standard during the three-month balloting period. If the outcome is positive, the modified document may then be circulated to ISO members as a Final Draft International Standard (FDIS). In the event of an affirmative vote, ISO 45001 is expected to be published as an International Standard by late 2016 / early 2017.

Source: www.iso.com

Tip of the Month- Know Safety, No Injury

As we go into the new year it is important to keep in mind that when it comes to health and safety everyone plays a part. As a team we need to all know and understand safety and the safety requirements. This is imperative in order to limit injuries and save unnecessary costs.

KNOW SAFETY, NO INJURY!